RobinThwaites

For EFP, IIII, Pro, Artemis - Steadicam part number 800-7204-03:- G70X 6" arm post with 5/8" top $132.00 For Archer, Pro-Vid, Zephyr, Scout - Steadicam part number 800-7204-04:- G70X 6" arm post with 1/2" top $126.00 Best Robin

Andrew, You have to remove the little stud that carries the cable, it is difficult and requires heat and brute force but can be done. It is not a screw in it just presses in but a twisting action will help get it out. You could sacrifice the cable to get something through the hole in the top to act as a lever and then replace the cable. The mystery screw goes through the gimbal handle on the Master and Ultra (1) to engage with the slot around the top of the arm post for low mode. Slightly disquieting as a fixture but if you think it through it is really safe. Sending a couple of things by e-mail. Robin

Hi Rupert Even better call us, you know where we are! Best Robin

Hi Mike Where are you? Can you send a pic to my email address robin.thwaites@tiffen.com ? Robin

Hi Matt Contact Rey Reyes or Dan Ikeda at the factory 818 843 4600 rreyes@tiffen.com or dikeda@tiffen.com. Alternatively shoot me a mail at robin.thwaites@tiffen.com and I will forward it. Best Robin

Hi Matt Your bearing is missing as well as the circlip, are you in the US? Robin

Dear Exovest Owners, Firstly a big thank you to all you early adopters of the Exovest, especially for your patience and support. Your feedback has driven important changes that we have integrated into the current design, and we’d now like to offer free upgrades to bring all vests up to that same standard. If you received your Exovest during or after December 2013, and has the scooped-out finger grips on the D shaped portion of the waist over-centre lever, your vest is entirely up to date. If not, there may be some updates available for you. Procedure will be one of the following: 1/ We ship you the upgrade package, including upgrade instructions. All relevant parts will be pre-assembled where possible, so the procedure should take you around an hour to complete, depending on how early your vest is. 2/ You ship it to the Steadicam factory in Burbank, California where we perform the upgrade and return the vest to you, we cover all shipping charges. 3/ You send it to one of our regional partners who will perform the upgrade and return the vest to you, again we pick up the cost of shipping. Should you have a vest in need of an upgrade or just want to check whether you require one, please email Kristi Davis in Burbank at kdavis@tiffen.com or call her directly at 001-818-567-7910. Please have your serial number available and we will verify what needs to be done and explain the procedure. Robin Thwaites Tiffen International

Hi Rupert Excellent camera, use the on board batteries, they don't weigh much. Robin

Hi Paul Look at the cables and the pulley wheels, sometimes it is a spring but often the cables. Can be caused by misalignment where someone has tried to de-tune the arm, just make sure they look parallel. Robin

Greetings All Tiffen International are hosting an open day with honoured guest Garrett Brown on Monday the 16th June. Also an opportunity to see the Steadicam range including a preview of the great new M-1 sled and some other gear only seen at NAB. We are hoping that Garrett will be able to present at least an abbreviated version of his great Moving Camera and of course he will be there to chat and answer questions. There will be the whole range of other Tiffen products together and importantly a running buffet with drinks. We'd love to see you but we need a guest list for security so please RSVP at http://www.flysteadicam.com/tiffen-open-day/ . Hope to see as many UK ops as possible and also anyone passing through the UK. Robin

Tiffen International are delighted to announce a SILVER THREE DAY Workshop from the 10th June to the 12th June at our usual venue of the SAE Institute Headquarters near Oxford. As usual the SILVER Workshop is for all Steadicam systems from the Zephyr upwards, instruction will be the usual Tiffen crew and maybe a few guests dropping by. Please e-mail either me, robin.thwaites@tiffen.com or Danny Hallett dhallett@tiffen.com for details and an application form, also details will be published on www.flysteadicam.com and FaceBook FlySteadicam or call us on +44 773 832 0850. Robin

Hi Axel Send me an e-mail at robin.thwaites@tiffen.com. Best wishes Robin

Hi All We have had a couple of places become available at our Silver Workshop (three days, all rigs) 3rd to 5th December in Oxford UK. Email robin.thwaites@tiffen.com if you are interested. Robin

Hi Zoran E mail me directly at my desk robin.thwaites@tiffen.com. I am running around a bit at the moment with scratchy internet but will pick it up when I can. Robin

Greetings all and some sad news. Some of you may know UK operator John Ward, if not look him up on IMDB - Full Metal Jacket, Prince of Thieves, Highlander etc. I have known John since around 1986 although he was operating before this with the first Steadicam Model 1 that entered the UK. Some of you may already be aware that John has been seriously ill for some time and things are unlikely to get better for him. In light of this he has asked me to see if anyone is interested in helping him clear his cellar where he has: 1 x Spintec 105mm spinning disc Rain Deflector. These are great devices, I used to sell them when I was at OpTex and they really work. Fits on matte box rails and needs 12 volts, not too much gyroscopic effect unlike the big 300 and 400mm versions. Was £2,500.00 (from memory) looking for £800.00 ono. 1 x Mk-V radio focus. Three channel with three motors (the blue ones) handset and receiver. This was one of only a few made but I believe that Marell Electronics would still be able to maintain it. Not bought from me but originally cost in the order £8,000.00 and would make a newbie operator a nice kit for around £2,500.00 complete. Please note this is a private sale on John's behalf and the items will be sold as seen (I have not seen them yet so am unable to answer questions until after the UK Silver Workshop ending on the 5th December) but do contact me at my Tiffen e-mail robin.thwaites@tiffen.com. Again, this is not a Tiffen sale, just helping a friend. Robin

Hi Paul The arm and vest is the same for both with the exception of the arm post which is cranked for the Merlin and straight for the Pilot and can be exchanged in a few seconds. Robin

Hi Domenico Tiffen three day workshop 3rd-5th December in Oxford, email me at robin.thwaites@tiffen.com if you are interested, we have a couple of places left. Robin

Hi Daniel It is probably fixable but line collapse as bright as that will probably have left a vertical burn mark on the tube. Tubes are pricey but you could probably get a complete used replacement for good money. Robin

Yes it will!

TIFFEN INTERNATIONAL AT IBC2013 As you may already know we have decided to have a rather different presence at this year’s IBC exhibition by focusing on what is most important for you, and for us. So we would very much like to see you at our Get Together or meet up at the show. Get TogetherThe traditional Tiffen Get Together will be on Saturday 14 September from 6pm till late at the Felix Meritis, Keizersgracht 324, Amsterdam. Please join us and our industry friends. There will be food and drink, and we plan to have a selection of new equipment available for your close-up inspection. Please let us know if you will, or will not, be attending by emailing James Carey at jcarey@tiffen.com ExhibitionTiffen will be present in the exhibition halls on the following stands: Broadcast RF hall 11 stand 11.F67 Cartoni hall 11 stand 11.E30 Chrosziel GmbH hall 11 stand 11.A67 Dedo Weigert Film GmbH hall 11 stand 11.G36 Polecam hall 10 stand 10.C49 The best way to make sure we see you in the exhibition is to make an appointment by contacting either Kevan Parker at kparker@tiffen.com or Robin Thwaites at robin.thwaites@tiffen.com or call the Tiffen office on +44 (0) 1753 783960. We look forward to seeing you in Amsterdam. Robin

Frederic What Sanjay said! Nice to see it on a Land Rover. Robin

Hi Ken As a goofy with this shot looking 45 degrees to my left I would definitely be checking over my left shoulder not right. Robin

Are you going to Broadcast India?

Hi Ahmet Please e-mail me at robin.thwaites@tiffen.com. Robin

Tiffen are very happy to announce two new Steadicam 3 day Silver workshops in the southern hemisphere. These are to be Wellington, New Zealand on the 5th-7th of June instructed by Rebecca Wilson-Jennings of Malaysia fame and then Sydney, Australia 31st July to 2nd August instructed by the legendary Harry Panagiotidis. The Silver workshop is a full on starter using all size of rigs and ideal for anyone just getting into Steadicam. Please contact Brett Smith bsmith@tiffen.com or look at Flysteadicam.com and Facebook FlySteadicam for more information. Robin