Greg Johnson

I have the vertical displacement plates, I haven't used the horizontal ones but as long as the camera is built out decently centered I don't see a need for it. but I could be wrong since I don't have experience with it

I think i've seen a post on the forum about with someone switching theirs but it does require rewiring the plate if you're comfortable with that. Other options are buying a whole new battery mount from Tiffen or getting a V mount to Gold mount adapter

Hey, I'm not sure about that model of flyer but I'd recommend getting a used Zephyr instead. I was able to fly most red and alexa mini camera builds with mine and it made for great starter rig. The vest and arm will be better and the sled has more power options that make flying heavier cameras and powering them through your sled a lot better

Hey, I had a zephyr starting out, it is a great starter rig but you will outgrow in very fast. I upgraded to a Pro within a year of having mine but it was great to get started at steadicaming. I was able to fly most Red and Alexa mini camera builds with it, even with anamorphic lenses if you have the right cables. If you get one buy it used and make sure to have it serviced before purchasing or right after purchasing. Also try to buy one with the second battery hanger included, it will help tremendously with keeping the post short and balancing cameras at the top of it's weight range. Be careful not to overload it though because the yoke can snap after a while. If you have the means definitely look at getting a used Archer or older Pro rig though, as you'll be able to keep those for a long time before needing to upgrade

Hey, I have two standard 9" Pro plates and the cinematic precision alexa plate and haven't found a need for another plate yet with my DB2. The only one I could think to be useful would be the Zalex long plate for unique long builds or the xcs sliding plate for the wave.

Hey Jason, There are two versions of the zephyr vest, a regular and a compact. If you have the compact version it will definitely not be good fit but at your height the regular might be rough also. GPI pro and Walter Klassen both take measurements when you order a vest from them to make sure it will fit right and both of them would be great vest for if you upgrade your rig in the future. If you get a GPI vest order it without the socket block and you'll save a good $1000ish Also Tiffen may be able to help you out if your contact them Directly, I use a pro so I can't say for sure

I have a Zephyr to Arri mini/amira cable if you're still looking

sent you a message

bump price lowered to $1200

bump, asking $100

I'm selling a Tiffen to Alexa Mini / Amira 24V cable. It's the smaller 3 pin for use with the Zephyr or Archer Sleds I purchased in April 2018 from Terry Available for pickup in Hollywood, LA or I can ship within the U.S.

Hello all I'm selling my Teradek Bolt 500 with 1TX and 1RX. Asking $1600, Located in Los Angeles but can ship to con. U.S. email steadigreg@gmail.com if interested. It's SDI only no HDMI. Purchased in January 2018 from Teradek and serviced in August 2019 by Teradek. Been in it's case since getting serviced. Works with newer version and SmallHD Bolt Monitors Selling because I don't use it enough. Come with - 1 x Protective waterproof SKB Case w/foam 2 x 2-pin Connector to PowerTap Cables 1 x 2-Pin Connector to 18W AC Adapter 6ft cable 1 x Hex L Key 2.5 mm size 3-5/6 inch length 1 x Hex L key 3/16inch x 2 13/16inch length 1 x Lightstand Adapter (1/4"-20 inch) 1 x Hot Shoe Adapter (1/4"-20 inch) 2 x SDI (BNC to BNC) Cable 1 x USB 2.0 Cable (A-Male to Mini-B)

Hello all I'm selling my Teradek Bolt 500 with 1TX and 1RX. It's SDI only no HDMI. Purchased in January 2018 from Teradek and serviced in August 2019 by Teradek Selling because I don't use it enough. Asking $2000 obo Come with - 1 x Protective waterproof SKB Case w/foam 2 x 2-pin Connector to PowerTap Cables 1 x 2-Pin Connector to 18W AC Adapter 6ft cable 1 x Hex L Key 2.5 mm size 3-5/6 inch length 1 x Hex L key 3/16inch x 2 13/16inch length 1 x Lightstand Adapter (1/4"-20 inch) 1 x Hot Shoe Adapter (1/4"-20 inch) 2 x SDI (BNC to BNC) Cable 1 x USB 2.0 Cable (A-Male to Mini-B)

Selling my Aero 30 system including all cables, plates, and accessories. Only been used to shoot one indie feature. The vest has been used a few more times as I rented it out to a buddy of mine but has added cross back straps. Other than that it’s all ready to go for ya in the pelican case with accessory organizer in the lid. I do also have a 5 foot c stand that was used to mount and balance it if you want that as well. If not I’ll take $100 off the price. I am throwing in the Steadicam guidebook and an extra V-Mount for the system. It currently has the Gold-Mount on it. Just looking for an excited new owner. -Steadicam Aero 30 system - 3 D&O 190 WH batteries (gold mount) - Dual battery charger - 1660 Pelican case - 1 pair smallrig 15mm rails - 2 smallrig rod clamps 15mm - 2 19-15mm Rod bushings - 19/15mm dovetail plate - 1 Alexa mini to D tap power cable - 1 RED to D tap power cable - 1 Lemo to D tap power cable - HMDI to mini HDMI coil cable - P tap to usb converter - SDI to HDMI converter - HDMI to SDI converter - D Tap to P tap power strip - miscellaneous Allen wrench and flat head screws - pack of bongo ties - gorilla Allen wrench Asking $6500 Located in Detroit, MI Buyer pays shipping. Email: jaycubrows@gmail.com if Interested More Photos Can be Viewed here https://www.facebook.com/marketplace/item/580483792482645/?ref=messenger_share

Sold

Hi all, I'm looking to buy a used or new Exovest, If you have one you're looking to part with feel free to email me at steadigreg@gmail.com or message me on here. Thanks, Greg

Update: I added cross back straps to the vest. Been meaning to do it for a while just got around to it

Bump

Hi All, I'm Selling my Zephyr kit The arm and sled have just come back from being serviced by Tiffen. Has some blemished and scratches but everything works perfectly. Only selling because I upgraded. $7000 Located in Detroit, MI. Willing to ship, Buyer pays shipping. More photos can be viewed here - https://drive.google.com/open?id=11ktvSvNraUAKbveOHnngcUu_K3R-2TkB Here's everything that's included Sled w/gold mount Arm w/ fleece bag Standard Vest Thermodyne Roller Case (Fits entire package) Sky Magic Monitor yoke 1/4 20 monitor mount Steadicam/Marshall Monitor Second battery mount (gold mount) Low mode Bracket Balancing weights Docking bracket Dovetail plate with screws 1 Hirose to 4-pin XLR/sdi monitor Cable 2 SDI cables 3 pin to Red Epic/Scarlet 3 pin to Alexa mini/Amira cable 12v 3 pin to female P-tap Cable 3 pin to Red One Cable 3 pin to 4 pin XLR cable

Sent you a message

Media blackout has some 3D printed ones https://mediablackout.net/collections/best-selling-products/products/sutherland-wrap-grip?variant=27984451590

Get some moisture wicking shirts and wear shorts. The shirts dry a lot faster so you won't be soaked all day.

I'm also looking! If anyone else has one that Jesse doesn't buy feel free to message or email. steadigreg@gmail.com

Joe Wilbur (Repairs) 1.818.567.7901 jwilbur@tiffen.com

Hello all, I'm looking to buy a weight cage or plate. Any tips or leads on where to acquire one would be greatly appreciated!