-
Posts
174 -
Joined
-
Last visited
-
Days Won
9
Everything posted by Kevin Jacobsen
-
4500
-
4700
-
Bump
-
Item is located in Miami Fl
-
I bought the vest earlier this year. Mainly just to try it out, but after a few practices and one attempt on set (about one hour of oping) , I decided to stick with my pro vest. It has two slight blemishes, one from missing the shoulder latch when putting it on. And one that was received during transit when I returned the vest to tiffen to replace a few screws that were missing on the chest plate. They have been replaced and locktite'd in. Essentially the vest is brand new, no sweating, comes with the extra pads and soft bag. $4800 Plus shipping
-
Newbie Introduction + questions
Kevin Jacobsen replied to Carlos Hernandez's topic in Steadi-Newbies
Where in Florida?- 5 replies
-
- newbie
- starter rig
-
(and 1 more)
Tagged with:
-
Steadicam being used as a tripod
Kevin Jacobsen replied to Omar Sawalha's topic in General Discussion
Sos plate on sticks to get it there. I've seen ACs use a quick release v-lock style for mounting an additional monitor for stick oping. Is there anything else they are popping on? -
I'm new to the wave, but have used it before and was shown how to balance for it (noga arm and tiffen weights). I noticed that the wave will drift from the level i have set it at over time. Has anyone dealt with this before? Is there something I'm missing? When it comes to docking, do you lock the wave first then dock or keep it running while on the stand? While the wave is engaged, how much of an issue is it to have an AC or DP influence pressure on it? ie. flipping the evf screen or accessing menus. Are there any other things about the wave that the seasoned ops here have come across that may not be obvious? I know Tom Wills made riser plates for a better weight distro without adding weight, which will be my next purchase.
-
Looking for a wave 1, preferably stateside.
-
Cinetronic 1 HD monitor
Kevin Jacobsen replied to Kevin Jacobsen's topic in Steadicam Marketplace - For Sale
New price 600 -
I have an extra one laying around. $80 plus shipping, located in Brooklyn. It will be sterilized before packing
-
MKV SLED v4 W/VOLT
Kevin Jacobsen replied to Kevin Jacobsen's topic in Steadicam Marketplace - For Sale
No longer selling the sled. Arm is sold. -
Are the Steadi-Cam Workshops "Worth It?"
Kevin Jacobsen replied to Connor Hargreaves's topic in Steadi-Newbies
Worth it -
Yeah I checked all that. Sometimes I put on fresh bricks to see if it changes, or reset the volt. The issue never persisted more than a few minutes.
- 33 replies
-
- volt steadicam
- volt
-
(and 2 more)
Tagged with:
-
Sometimes I can't get the vault to be level no matter how many times I trim it. What seems to work is cycling the power a few times, but under a time crunch, it could be very annoying. I just switch it off and operate normally but it's an issue that I've seen multiple times and I don't know what causes it.
- 33 replies
-
- 1
-
- volt steadicam
- volt
-
(and 2 more)
Tagged with:
-
Sold
-
1500
-
Clipper 2 sled modified
Kevin Jacobsen replied to Kevin Jacobsen's topic in Steadicam Marketplace - For Sale
Sold -
Better pictures
-
$1650 With MDR diving board. Optical Support 15mm rod adaptor 175 with top stage or 200 by itself.
-
Clipper 2 sled modified
Kevin Jacobsen replied to Kevin Jacobsen's topic in Steadicam Marketplace - For Sale
Sale pending -
Clipper 2 sled modified
Kevin Jacobsen replied to Kevin Jacobsen's topic in Steadicam Marketplace - For Sale
$4500 whoa! -
TIFFEN ULTRA 2 SLED WANTED
Kevin Jacobsen replied to Vidhichand Jaiswal's topic in Steadicam Marketplace - Wanted
I have a clipper 2 -
This comes with the MDR Diving board. I will add the 15mm rod adaptor with rods for an additional $175