Damien King

So to be clear what 79K USD gets the potential buyer. Full Arri Trinity 2 with master Grip set. Super Post with travel case, long cable Radio Module 2400 for RCP remote control, therefore not required by operator to carry on rig. Full OCU-1 controller for remote roll, till etc. DUB-1 (ring to quick production mode) Enough weights for any build, plates etc, lens support, cables x 2 For additional $$ will sell B mount batteries (6x 155) plus quad charger in road case. The kit is in new condition and can be shipped Worldwide with buyer paying shipping. Happy to sort out from my end.

Below is the full invoice for the parts purchased over the time I have had the rig. Plus my carry case for the super long post and long post with long cable. Listed is all the parts available. Happy to sell the rig with any or all of the parts available. I won't part out until the rig is sold. Thanks. Please contact me at damienking@icloud.com 3182008123.King Motion Productions.pdf

Happy to split the kit out and just sell the basic Trinity 2 kit without super post, battery plates or radio modules. Get in touch. damienking@icloud.com Thanks

Kit also comes with the Arri allocated road cases for head and sled. All the above components fit in the cases and will be able to travel worldwide. I'd estimate $850-$1200 USD freight costs to any location worldwide. Contact me for any questions, FaceTime to check the equipment out or email me @ damienking@icloud.com

This kit has the radio modules included, therefore RCP can be left on the stand, with DP/operator or assist for control. Very handy and a must for technical shots. Can also sell this kit with OCU-1 for roll/tilt control.

Selling a full Arri Trinity 2 kit. Full kit, super post with cable. Head Case/Trinity Case/ Weights ( 6x25, 6x 150, 2x 300, 2 x 800 donuts) Full set of cables x 2 plus 2x short head cables + 1 long cable 3 x sets of batteries plates. (AB/Vlok/Bmount) 2 options for monitor mounting on gimbal/Small HD 503 monitor Replaced bottom rods for steel 19" rods. $79K USD Please contact damienking@icloud.com for any information, a full list of kit with Arri prices attached.

Hello everyone, Considering converting my rig across to Dionic 26 volt 98 Wh batteries/plates moving forward. Does anyone have any thoughts if this is bad or good? Love to hear your thoughts. Thanks

Bump

Sold

Sold

Pending

$5000 USD or best reasonable offer. Front, back mount with heaps of spares and padding plus a neoprene bag and pelican case for travel options. Buyer pays shipping

$8500 USD or best offer

damienking@icloud.com if you'd like to contact me via email. Thanks

Selling my back up X1 arm, hasn't been used and have decided to move it on. 9000USD or best offer. Don't wait and get a brand new arm without the wait. Comes in a custom case with lowmode bracket. Can ship worldwide at buyers expense. Arm located in Australia

Bump

Selling a used Xspine vest with front and back mount options as well as the back relief pad. Kit has all the extras with it, a pelican case, soft case and additional foam, buckles. Asking 5500 USD or best offer for the lot. Can ship Worldwide, vest located in Australia

5500 USD or best offer. Thanks

Make an offer, needs to be out in the world helping monitors.

Selling a Flowcine XR3ach in new condition. Great bit of kit but no longer required. Photos attached. Buyer pays shipping. Australia based. 6k USD

Bump

Sold

Arri Trinity Rig has sold. PLC wheels still available 5K Thanks

Selling Full 12/24 Volt Trinity Package. The Equipment is located in Australia. Willing to ship anywhere in the world at buyers expense. Trinity has been fully service by Arri Australia and is ready to go. 45K USD K2.0010282 TRINITY 12/24 Volt from Factory K2.0010287 TRINITY Joystick Monitor Mount K2.0010569 Gimbal Handel Extender for 1.8in Gimbal x 2 K2.0010288 TRINITY Battery Mount, V-Lok x 4 (1 locking damaged) additional v-lok Anton Bauer plate plus flat plate for mounting (links etc.) K2.0010319 Docking Bracket, 1.8in K2.0010290 TRINITY PWR, Lemo 1B 4pin to 1B 4pin x 2 K2.0010470 Trinity PWR, Lemo 1B 4 pin to 4pin XLR x 2 K2.0024100 TRINITY PWR, Lemo 1S 3pin to 1S 3pin (only for TRINITY upgraded to 24V) x 2 K2.0014805 TRINITY Joystick Main cable (single BNC-SMB cable) x 2 TRINITY Joystick Main cable BNC ONLY K2.0014804 TRINITY power cable for Joystick Main cable – spare SMC cable for the TRINITY Main cable (K2.0014805), POWER ONLY. K2.0014803 Joystick Pwr. cable for Transvideo Starlite and SmallHD 503, 2pin Lemo Transvideo Starlite monitor and SmallHD 503 monitor in package Joystick to Transvideo Starlite 5 pin cable K2.0010296 TRINITY Ext. Power Cable, D-Tab to 1S 3pin K2.0014264 TRINITY and Artemis Post Extension 3B, 10pin length 8.5in, diameter 1.8in x 2 K2.0010466 Artemis Rain Cover Lower Sled K2.0010299 QL Camera Plate MAXIMA / TRINITY K2.0035956 SSB-1, Stabilizer System Bracket for TRINITY, MAXIMA, SAM plates – mounted to the TRINITY Head x 1 Donut Weight for Trinity - 800gram with inserts.(1.8/1.5") Custom dual loomed BNC cables x 2 Accessories K2.0010434 Hex Key 4mm/5.32in K2.0040046 CSS Post Tool for Artemis and TRINITY 3D printed TRINITY Centering Tool HEADLOK and Roll Lock Bracket for TRINITY TRINITY-Bumpers, 3D printed K2.0016274 Case Artemis Gen. 1, Rig, Pelican 1615 Air, with foam inlay TRINITY Head will be shipped in a SKB 3i-2317-14BE case Additional: Arri Trinity MSP-1 K2.0015385 PLC Wheels -3 wheel package for DP/operator control (Comes in the PLC travel Case) Any additional cables or related accessories not listed will also be included.