Jump to content

B&C output at base of telescope not working


candace coons

Recommended Posts

Hi,

Been having issues with my rig for a few weeks, thought it was due to the cold, but turns out its not. So here is my issue; The B&C output is not working from the bottom of the telescope (the monitor works fine, so I know its not that), and lately I've been having to connect directley from the camera to the monior. Has anyone else had this happen,what is it, why is it not working, and if anyone knows where in NYC I could get it fixed (or if I need to send it out).

 

Thank you,

Candace

Link to comment
Share on other sites

  • Premium Members

Candace,

 

Couple of things - first of all, you should always mention what rig you have in threads like this. Since I'm bored, I looked up your post history, and you appear to have an Archer 2. Most people won't do that work for you though - if you want an answer, you should at least give us enough information to solve it! (EDIT: I did just see that you had it listed in a tag - still better off to put it in the post, since I know I didn't see that until after I posted!)

 

Also, for the record, it's BNC - Bayonet Nut Connector. No "and" in there.

 

To answer your question though, the BNC on the base is labeled HDSDI - meaning that it connects to the HDSDI line on top of the rig, not to the "Video" line. The Video line connects directly to the monitor. Unless you put the same signal down both lines, you're only going to get signal out of the connection you put it into.

 

Hope that helps.

Link to comment
Share on other sites

  • Premium Members

Tom,


I've always been under the impression that the origins or the acronym BNC were shrouded in mystery. My preferred interpretation has been British Naval Connector. Bayonet-Nut makes sense, however Wikipedia states that it's named after the inventors Paul Neill and the Carl Concelman, thus the Bayonet Neill-Concelman (as opposed to the TNC, the Threaded Neill-Concelman). In any case it's definitely BNC and not B and C.


Edited by Carl Wiedemann
Link to comment
Share on other sites

Thank you all for the responses. The problem started when I was on a job with a A RED one. I had BNC from the camera to the HDSDI on the top stage for my Archer 2. In the middle of the shot the image on my monitor started going in and out. I figured out that the HDSDI out at the bottom of the rig going into my monitor was the problem. So just ran a BNC from the camera to the monitor. I was just wondering if there was place in NYC that i may be able to take a look at it or fix the problem.

 

Thank you,

Candace

Link to comment
Share on other sites

  • Premium Members

I was just wondering if there was place in NYC that i may be able to take a look at it or fix the problem.

 

I am just baffled every time I read a request like that. When you buy a Steadicam product, don't you get an address or a phone number for questions or emergencies or things like that? Am I missing something?

 

Try:

 

The Tiffen Company

90 Oser Avenue

Hauppauge, NY 11788

Tel: 631 273 2500

Fax: 631 273 2557

Toll Free: 1 800 645 2522

Email: techsupport@tiffen.com

Link to comment
Share on other sites

  • Premium Members

I have to say that I have had a lot of issues contacting Tiffen these past weeks. I too ask question on the forum prior to contacting the company. It gives you a sense of how spread the issue is and sometimes how to fix it without sending the rig back.

Past that point it is true that before asking a question. I tend to read every available literature.

Link to comment
Share on other sites

  • Premium Members

sounds like: too big to fail....If the company does not know your name, you are apparently out of luck... Dealing with companies like Preston, Pro, XCS, Cinetronic, Bartech, Transvideo,... is simple and effective, they know your gear and you...and they understand that you are not a rental house with 5 rigs on the shelf, instant service is why I buy from local, smaller, trusted & tested manufacturers.....downtime get's expensive, fast

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...