Scott Baker

SOLD

Reduced to $4,000.

Or make me an offer, let's find this a home!

Tiffen Ultra vest. 
A few years old, great condition and clean. 
It has the Tiffen socket block but I have a Pro socket block if you want that instead. 
Asking for $4,500 or best offer. 
Located in Los Angeles. 
Will ship in US. 
thanks!

Interested. 
messaged you. 

Interested in the vest only. 

SOLD

I’m a bit sad to be letting go of my trusty Ultra 1 sled, but I’ve upgraded to the M2, and hopefully we can find a good home for someone just starting out or looking for their first “big rig”. 
This is the 4 section super post with motorized tilt head. 
It’s been upgraded with a HD-SDI line and is V-mount. 
Included is the Transvideo HD6 Superbright monitor (which is an absolute tank), and p-tap to xlr power cable. 
Also I’ll throw in the dock with Hill bracket. 
One long plate and one short. 
And custom cut Thermodyne hard case. 
 

Asking $8,000 obo, located in Los Angeles and prefer local but willing to ship at buyer’s expense. 
 

Looking to replace my stolen gear. 
G-70x or Pro Arm or equivalent. 
Ultra 2 or Pro Vest or equivalent. 
In Los Angeles preferred but willing to pay shipping. 
Thanks!!

Willing to sell just the vest?

Would you sell just the exovest?

thanks. 

Bump.
Surely someone wants to take these off my hands and out of my apartment! :)

Hey all,

I have 9 PAG batteries and 2 chargers from my old Master series sled that I no longer need.

They most certainly would need to be recelled, a couple might hold a little charger but haven't tested them.

Free to whoever wants to pick them up in Hollywood...

I have a Cinetronic Digital Level for the Gen 2 Monitor. CDL v1.0

The monitor crapped out and has been replaced with a Transvideo, so I don't need this anymore.

Works perfectly and will included 2 of the 4-Pin Lemos to connect to the monitor.

Make me an offer.

Located in Los Angeles, willing to ship.

Problem solved. Robert Luna and Hugo from Steadyrig were both able to help me out.

The screw that goes into the spring of my 3A arm is sightly damaged (bent/stripped) and doesn't go smoothly into the spring.

Anyone have a replacement or know where I can get one?

Sled is sold.

Still have the batteries and chargers.

And the PAG to Gold mount plate.

Make an offer.

Bump.

Make me an offer!

I have an old Master Series Cinema sled that took a fall a while ago and has been just sitting in my closet.

The only damage appears to be the extended element on the top stage and the old CRT monitor.

All of the electronics still appear to be functional and the top stage itself still solid.

The gimbal was serviced right before the accident and is still smooth as butter.

I also have 9 PAG batteries and 2 chargers.

Most likely need to be re-celled.

As well as a PAG to AB Mount adapter battery plate.

Make me an offer!

Located in Los Angeles and prefer a local purchase, but willing to ship if buyer pays.

I noticed some left-right play in the top stage of my Ultra Cine sled and then discovered the culprit could be a missing pin of some kind about the size of paper clip. It appears there should be three but the front one is gone. Any idea what these are? Where can get some kind of replacement?

Lawrence, Id be eternally grateful if youd do me the favor of sending that. Scott@steadicam.LA

Thanks!

Two times I have emailed firmware and uploading instructions to those asking for help. Never heard back from either. Must be the new way.

Thanks Tammy. Unfortunately not, that just navigates you to the factory reset. Im able to get the monitor up every ten or so tries by holding down Left and Power but it wont boot up reliably.

These are the instructions from Chris when it happened to me. It happened at least twice. Once when an assistant went in the menu system.

Hope this helps. "Power the monitor on, press menu, then right 7 times, then left once, then down once then right once".

That link is dead.

Anyone have the firmware and instructions?

Lionel,

 

look above at the prior suggestions.If that does not work try and reinstall the firmware using a PC computer, not Mac(not supported). You can download the firmware and find instructions here: http://cinetronic.com/forum/

Good luck.

The tape on my sled's hand grip is past its prime and needs replacing.

Looking for recommendations.

Thanks!

I'll take it. Sent you email.

I'd try to keep more consistent head room on the actress.

And on the shots where she's entering the frame, start your move slightly ahead of hers so it doesn't feel like you're reacting to her movement, but rather moving in concert.

Keep practicing and fly safely!