-
Posts
240 -
Joined
-
Last visited
-
Days Won
3
nick franco last won the day on October 6 2017
nick franco had the most liked content!
Reputation
11 GoodAbout nick franco
Contact Methods
-
Website
http://www.nickfranco.com
Profile Information
-
Location
San Fernando, CA
-
Rig
PROII
Recent Profile Visitors
-
Preston MDR-2 with brackets and cables
nick franco replied to nick franco's topic in Steadicam Marketplace - For Sale
SOLD -
Preston MDR-2 with brackets and cables
nick franco replied to nick franco's topic in Steadicam Marketplace - For Sale
n Los Angeles Preston MDR-2 G4 Blue dot $1500 Preston serial cable with USB adaptor command cable -------------------------------------- FilmFrog bracket $50 -------------------------------------- Cine Tape interface cable $200 Pana Tape interface cable $200 --------------------------------------- Run cables $50 each 3 pin -MDR 4521 run 2xSony 4435 run 2x Ari 11 pin Fischer run 4520 Red run 4543 Panavision run cable 4522 AATON run4524 2x Movicam 2 pin run cable 4523 ---------------------------------------------- Power cables $50 each 3 pin to MRD power cable Pana to MDR power cable 4472 Anton Bauer Ptap to MDR power 4473 -
Preston MDR-2 with brackets and cables
nick franco replied to nick franco's topic in Steadicam Marketplace - For Sale
Sent from my iPhone using Tapatalk -
$3000 or best offer. Located in Los Angeles Preston MDR-2 G4 Blue dot PRO dovetail mount FilmFrog cheese plate Preston serial cable with USB adaptor command cable Cine Tape interface cable Pana Tape interface cable PRO- MDR power cable 2x 3 pin -MDR 4521 run Sony F5/F55 run 2xSony 4435 run 2x Ari 11 pin Fischer run 4520 Red run 4543 2x Panavision run cable 4522 AATON run4524 2x Movicam 2 pin run cable 4523 3 pin to MRD power cable Pana to MDR power cable 4472 Anton Bauer Ptap to MDR power 4473
-
Digital level that mixes in w/HD cable?
nick franco replied to Dan Coplan's topic in Video Assist and Video Accessories
-
Preston DM-1 with Hill rosette $1500.00
nick franco replied to nick franco's topic in Steadicam Marketplace - For Sale
Motor is sold. -
Preston DM-1 with Hill rosette $1500.00
nick franco replied to nick franco's topic in Steadicam Marketplace - For Sale
I've been expecting you. -
Gimbal Arm Post clamp placement (Pro Arm)
nick franco replied to Robert Medina's topic in General Discussion
The clamp needs to stay on the top, otherwise you're not getting the benefit of the bearings. The inner race of the upper bearing sits slightly higher so the clamp can ride on it. -
My feet are 10.5 EE, New Balance 990 has been my work shoe.
-
Also, http://www.wihatools.com
-
PRO2 Battery - Any reason why this is a bad idea?
nick franco replied to William Demeritt's topic in Sled
He paid for it by only filling the Hummer half way. -
Does it have cap screws on the face plate? Might be able to open it that way, but that would be wrong.
- 32 replies
-
- Anton/Bauer
- battery
-
(and 2 more)
Tagged with:
-
Pull the canisters and clean the two pins and their mating surfaces on the chassis. Not sure what vest you have but I had a similar noise that turned out to be where the plate that holds socket block meet the center upright spar. Took it all apart, cleaned it and reassembled it, no more noise. Pro vest.
-
Try Robert Luna , he might be able to make an adaptor post?