Alan Mehlbrech

SOLD. Thanks for all the emails- Alan Mehlbrech

FOR SALE- ANTON BAUER 6 DIONIC 90'S 4 DIGITAL TRIMPACs 1 TWQ QUAD CHARGER 1600 Pelican padded case Light use. All batteries were just tested. Results back from Anton Bauer were that all batteries were showing above 90% life. $2500.00 usd +shipping Thanks, Alan Mehlbrech alanmehlbrech@gmail.com 917.753.1146

Hello All, I ran into this as well with my MKV- Chris Konash ( www.eastcoastcables.com ) -solved the problem by making a jumper at the base of my V2 electronics and using the AR lines up the sled to run two 12volt lines up. He then made a "Y" cable at the top to power the camera. Everything is 12 volt on the camera so tell the AC to have a Cinetape cable that is for 12v. Otherwise I have had great run life on both Powercubes and AB HC's. Regards, Alan

I always find this short essay from TJ Willaims helpful.... http://www.camera-person.com/philosophy.html the other one that has helped me is- "When you get 40 million will do the movie your way." Happy New Year. Alan

Sold. Thanks for all the interest.

Sold. Thanks for all the interest.

Sale Pending.

Bartech with M1 Motor Transmitter # 1.0003 Receiver #1.0003 M1 Motor # 1.0106 Complete Set of M1 Gears and Brackets 3 motor cables 2 jumper power cable 2 Delrin Marking Rings 8 Marking Strips 1 Panavision 24v to 16v cable 1 Anton Bauer "P" Tap Cable 1 12v Genesis Power cable 1 Direct Connect Control Cable Run/Stop Cables 1 Arri 11 pin 1 Arri,F23,F35,Genesis 1 Panavision 1 Red 1 Moviecam $4400 Buyer Pays Shipping. Thanks, AlanMehlbrech(at)gmail.com 917.753.1146

Bartech with M1 Motor Transmitter #1.0028 Receiver #1.0028 M1 Motor # 1.0331 Complete Set of M1 Gears and Brackets 2 motor cables 1 jumper power cable 2 Delrin Marking Rings 8 Marking Strips 1 Panavision 24v to 16v power cable 1"P" Tap power cable $4000 Buyer Pays Shipping. Thanks, AlanMehlbrech(at)gmail.com 917.753.1146

SOLD. Thanks for all the interest. Alan Mehlbrech

Steadicam Masters Elite Sled Sled 24/12volt #195192 24 volt Battery Mod (powers a 435 @ high speed) Docking Bracket 2 Wolfvid LCD Monitors Cables : Panavision 24v LW & Millenium Arri 24v Movicam 24v 12 volt XLR Preston Power Modulus ...etc. 2 Sled/Camera Dovetail Plates 8 Batteries ( less than a year old) 2 Charging Stations- 4 in Pelican case -2 in custom “on set” case Bartech ICBM built in sled for Battery readout - gives you readout on Batteries in real time, warning lights and voltage draw ...etc. Pelican 1600 for Batteries, Anvil Case For Cables etc. Custom Metal Sled Case with wheels Mounting Slider for on board recorder A single channel transmitter (channel 14) Backup Gimbal Barring...... everything else I have that goes with this rig. Asking $18,000 USD - buyer pays shipping etc. I have more pictures I can email. Thanks- Alan Mehlbrech alanmehlbrech@gmail.com alanmehlbrech.com

For Sale: Steadicam Masters Elite Sled Sled 24/12volt 195192 Docking Bracket 2 LCD Monitors 24 volt Battery Mod (powers a 435 @ high speed) Lots of Cables : Panavision Arri Movicam 12 volt XLR Modulus Etc… Camera Plate x2 Batteries x8 Charging Station- 4 in case -2 in “on set” case Bartech ICBM built in sled for Battery readout Backup Gimbal Barring Battery holder for Stand Mounting Slider for on board recorder Pelican 1600 for Batteries, Cable etc. Custom Metal Sled Case with wheels $18,000 USD - buyer pays shipping etc. Thanks- Alan Mehlbrech alanmehlbrech@gmail.com alanmehlbrech.com

hello?

Hey All, How do these compare to the IDX powercubes for Steadicam purposes? Thanks In Advance, Alan

Hey Philip, I made a slavecam out of wood at a workshop in Maine. 2 full sheets of 3/4 ply and 10 2x4's 8' long. I married the 2x4's in pairs to make 5 4x4 handles. One sheet of ply on top and the other on the bottom. The 4x4's came out of the 4' side of the ply sandwich equally to make handles . Then we all got together (10 people) and lifted our op and talent up about 3' in the air... This lasted 20 to 30 seconds before the faces turned red and we lowered them down again. One take . -if you can make it though to the end that is when the slavecam comes into play. 4:00 till the end. We all had fun making it and Paul was surprised at the Friday night showing even though he was in it... Alan Mehlbrech

> Viewing services will be on Thursday, August 21 2008 from > 2-4 pm and again > from 7-9 pm. Service will be held at Holcombe-Fisher > Funeral Home, 147 Main > Street, Flemington NJ. > > Funeral Services will be held Friday from 9:30-10:30AM in > the Flemington > Presbyterian Church, 10 East Main Street, Flemington NJ > > Andy and Kathy will both be cremated. > > Directions can be found on line at www.holcombefisher.com > > Andy's and Kathy's Obituary can also be found at > http://www.holcombefisher.com/obits/obit.cfm?obitid=1257 > > In Lieu of flowers, memorial contributions may be made to; > > The Kathy and Andy Casey Memorial Fund > c/o Harry Copeland > Commerce Bank > One Royal Road > Flemington NJ 08822

You mentioned union house- see if there are any avenues through the local that can get this taken care of. Alan Mehlbrech

mr fowler, iphone user as you seem to be -add a mcmaster button on your screen... http://www.mcmaster.com/ pg 2787 love your work, Alan

I think I saw a cell phone velcroed to the front of a vest once? Brant I think you were there? Pictures? And thanks for the Antlers V2 . They rock. Big Love , Alan Mehlbrech

maybe the pictures are below?? Alan

You know how people look like there dog... I'm just saying - Alan Mehlbrech

None of the beat poets could have said it better. let's all snap some fingers for our brother. This is the best post EVER.

cold brooklyn piers at night ... I find the deer skin or goat skin glove works good. Remove what tips you need to feel comfortable with sissors. Tennis tape on the gibal. The trick I like is to take the small shake up hand warmers and tape them (black paper tape-see dolly grip) to my wrist so the blood going to my hands is warmed and the warmers are mostly out of my way. or a campfire is always nice ... Alan