Kenny Brown SOC

Hi there

I have a Yaeger Junior with a mast and a Mitchell mount on it that I want to sell.  Barely used.

 

Kenny

Deal done.  No longer available.

Thanks

Hi there

 

I have one with the level etc in a Cam Jam yoke in LA. 

 

Cheers

 

Kenny

Anyone want a Tiffen Blue Whale tool?  Doesn't fit anything I own and too good to throw away.  Think it's for a Ultra 2.

I'll  slow mail it anywhere (or pick up in Los Angeles) and you give $5 or equivalent to anyone you think could use it.

 

Cheers

Sold

BTT

 

Taking all offers

Never used battery back bracket for Small HD 702 with friction control mechanics for Quattro monitor arm.  I upgraded to a 703 before I had a chance to use this on a Steadicam.  Cost $290 plus the shipping.

 

https://shop.cam-jam.de/product/battery-back-for-smallhd-702/

 

$160 or best offer.

Thanks

 

Kenny Brown

Los Angeles

 

Sold.

btt.  Will consider splitting

BTT $1000 obo

Got a 2 inch ring available.

 

Kenny

Los Angeles

Tiffen Ultra 1 sled

Long and short Tiffen dovetail plates

Tilting top stage(upgraded bolts and brace)

HDSDI down the post (Terry West)

Long nose section cut down, connectors replaced with HDSDI BNC, 12/24V 3 Pin 0B Lemo and 0B 12V Lemo (same polarity as Arri/Teradek/Preston etc).  Back of the top stage still has 2 x 12/24V 2B Lemo and Hirose 12V

Original 4 stage integrated ‘super post’ 

Gimbal upgraded with Ultra 2 latch and just serviced and balanced by Robert Luna.

Bottom K section removed and rewired with custom 3D Printed Case (Allen Rencher) with switch, LED, HDSDI, 3 x Lemo 2B 12/24V power connectors for batteries, 0B Lemo 12/24V and Hirose 4 pin

12/24V power from two V-mount plates

Accessory dovetail plate for Tiffen 3^rdBattery mount

2 x V-mount to Anton Bauer battery plates

Low mode bracket

Hill docking rings top and bottom

Gorelock 2 balancing/docking bracket with tilt function

Gorelock 2 docking bracket for cart

Power cable Lemo 2B to 12V 4 pin right angle XLR power cable (brand new)

 

Transvideo HD6(blue knob, 1000Nits) with Virtual Horizon, Scopes etc on Cam Jam yoke (6.5mm) and rod.  Note you will need a Cam Jam Quattro Monitor arm to complete this sled. Already have the custom derlin collar to fit.  Comes with 3 pin Lemo power, Hirose power cables and two composite to 8 pin cables.

 

Custom Inner Space flight case you can drop the whole built sled in.

 

Very versatile sled and served me well for years on TV and features, now moved to M1/Volt.

Los Angeles

$10,500 or best offer

 

2 x V-Mount VL-4S Simultaneous chargers – work perfectly. 

 

8 IDX E-HL9S 88Wh 10 Amp/120w Batteries, some branded Tiffen Powercube.  3 of these have been re-celled by Ritter (July 2017, Dec 2017 and May 2018). The others are older and work but I’m sure they don’t provide anywhere near the capacity they should.  Ritter charged $165 a piece plus shipping to redo these batts and I recommend them.

 

1 x Sharkfin to put 2 batteries on one mount

 

Pelican 1600 padded case to hold everything and room for more.

Located in Los Angeles, buyer pays shipping.

$1400 OBO

It fits well in-between the bottom of camera and top plate of the head. I don't have a photo but if you're looking at the back of the camera the microforce cable goes off to the right and the handle just lies down horizontally in there. You can put hard side velcro on both sides to stop it slipping around. As for operating, it's always a bit awkward, but I just hold the wheel handle between my pinkie and ring finger, then operate the microforce with the other fingers and thumb as usual.

 

Cheers

 

Kenny

Sold. Thanks.

Still available, but don't think its worth shipping to UK.

 

Cheers.

Sold.

pics

 

Hypercam HC3 cage with flight case, all tools and Pro post - unused.

 

Bought this for a show with lots of car to car work that got cancelled before it showed up.

 

Put it on in a rental house once.

 

If you don't know what this is see this thread.

 

http://www.steadicamforum.com/index.php?showtopic=18165&hl=hypercam

 

or

 

http://miamidp.com/hypercam.html

 

Thanks

 

Kenny

 

 

Selling my trusty cart

 

Filmtools Magliner Jr with Backstage 8 inch wheel conversion kit, 24 inch bottom and top shelf,

3rd shelf (sound mixer style - I kept my arm on here)

Lockable drawer (with foam cut for MDR3 and accessories)

Swing away handles

Steadicam Riser Brackets from Backstage to hold American Grip Riser

Baby pin mounted on top shelf

Led lights included with P-tap and dimmer

Tool free upgrades

Add a riser and bumper from Backstage and

you’re good to go

$800 obo

Located in Los Angeles

Kenny

Hi

 

I had the same problem and Burbank replaced the pin and glued it - fixed. Took a few days.

 

Cheers

 

Kenny

Hi there

 

I have one to sell. Unused - bought for a job that was cancelled. PM me.

 

Thanks

 

Kenny

Gone. Thanks

Hi all

 

I've got a nasty old Pelican case with nice Innerspace cut foam on the inside for a Teradek 2000 kit. Interior is 11.5 x 17 inches. Too good to throw out. If anyone in LA wants to pick it up, drop me a line.

 

Cheers

 

Kenny