Gareth Manwaring

 

Hello Steadicam peeps. I’m looking to off load some batteries for some lower wattage ones. I purchased half of them in 2021 and the other half in 2022 you can see by the cycles count which is which. Brand new they go for a little under $500 I was going to start at $350/battery and see is that works for someone. 

 

$2,800/8 batteries OBO buyer pays shipping. 

 

Also note that some or all of the batteries might be out of warranty and Anton Bauer suggests keeping the batteries charged at all times for best results. 

 

-Gareth

Sold. Thanks. 

Hello Steadicam Peeps. 
 

Pics and inventory below. looking for $13,000 or $6,500/kit. Buyer pays shipping. 

-Gareth

 

 

Bolt 4K breakdown.pdf

Hello Steadicam peeps! I was wondering if anyone can share their average battery life that they have gotten before a battery has stopped working compleatly? Brand and years worked would be great. 

-Gareth

Close ups of single channel below. 

Hey Lane,

I’m pretty sure it’s has the antenna attachment at the top. (I can get a pic for you later) but what switch? And where would that be located?

-Gareth

Bump $21,000 OBO

Bump. $22,000 OBO. 

Bump. $23,000 OBO. 

Bump. $24,000 OBO. 

I have a complete Preston kit for sale. Looking for $25,000 OBO inventory and pictures below. Buyer pays shipping unless they would like to pickup in Brooklyn, ny.

-Gareth

Preston For Sale.pdf

Hello. How much are you selling your kit for?

Hello Craig. Where are you located?

-Gareth

This is no longer available. 

This fits the Pro Post at 1 1/2"

 

-G

I have these two items for sale. If interested please make a offer. Buyer pays shipping. Located in NYC. 

Bump $4,200 OBO

I have moved on from this monitor to something that’s brighter but this one still works great with no scratches. I was using it in my Quattro II yoke on my pro. So if somehow that works for you the cables and kit are included. 
 

Tvlogic LVM-075A s/n LV075AP0228

8pin RS to tvlogic 36”

8pin RS to tvlogic 24”

Plastic hood

Quattro II Mounting kit - TV Logic LVM-074W (two knobs in the picture you will need to have the QUATTRO II postclamp rods and yoke that match which are not included)

 

Asking $1,250 OBO buyer pays shipping.  

I have a well maintained cinetape located here in NYC for sale. Asking $5000 OBO. Buyer pays shipping. 
 

• 1x Cinetape Readout S/n 30546
• 1x Cinetape Horns s/n 35625
• 2x Cinetape sensor cable
• 1x 3pin RS to 3 pin RS cable
• 2x 3pin lemo to 3pin RS cable
• 1x 1200 Pelican Carrying Case
• 1x backup knob

 

Hello Team,

Does anyone have a low mode bracket, f-bracket or similar for the G70x? Also does anyone have a 12” riser for the G70x? Thanks. 
 

-Gareth

I’m interested. I’ll PM you. 

I would love this arm! Is it still available?

Koji,

     I recently tried to send in my pro gimbal to tiffen to have the Volt attached and tiffen was unable to make it work. Tyson at Tiffen suggested I get the whole Volt setup instead of trying to convert my pro gimbal over. They sent me the whole Volt kit with a disclaimer that it might not fit perfectly and I might possibly need to send in my sled post to have it fitted. In the end the step down rings they sent with the Volt fit great. Now I just keep my pro gimbal as a backup. 
 

-Gareth

Sold. 

Hello. I have recently taken these units off of a job. Gave them a good once over, updated all the units to the latest firmware, paired them up and tested them. There are minor scratches and hits to each unit. The arrays still work but they took the most damage and have been patched up a little.

Set 1 $12,000

Case

1TX SN 199601064 V 3.1.9
1RX-1 SN 199701764 V 3.1.9
1RX-2 SN 199701765 V 3.1.9

2 different TX brackets

4x TX antenna straight
2x TX dome antenna
10x RX antenna
7x array Cables

Array (cracked on the top)
Yoke
2x 750 pin bracket

Wooden camera:
1x nato lock kit
1x v-lock base station
1x ultra arm mini monitor mount

2x p-tap to 2-pin
1x 2-pin to 2-pin
1x 3-pin to 2-pin
2x hdmi to hdmi
2x short BNC
2x USB
2x AC to 2-pin

 
Set 2 $12,000

Case

3TX SN 199601065 V 3.1.9
3RX-1 SN 199701766 V 3.1.9
3RX-2 SN 199701767 V 3.1.9

2 different TX brackets

3x TX antenna straight
2x TX dome antenna
10x RX antenna
7x array Cables

Array (cracked on the bottom right with tape over it)
Yoke
2x 750 pin bracket

Wooden camera
1x nato lock kit
1x v-lock base station
1x ultra arm mini monitor mount

2x p-tap to 2-pin
1x 2-pin to 2-pin
1x 3-pin to 2-pin
2x hdmi to hdmi
2x short BNC
2x USB

2x AC to 2-pin
2x plug adaptor bags

Set 3 $12,000

Case

2TX SN 199601063 V 3.1.9
2RX-1 SN 199701762 V 3.1.9
2RX-2 SN 199791763 V 3.1.9

2 different TX brackets

4x TX antenna straight
2x TX dome antenna
10x RX antenna
7x array Cables

Array (cracked on front and bent)
Yoke
2x 750 pin bracket

Wooden camera
1x nato lock kit
1x v-lock base station
1x ultra arm mini monitor mount

2x p-tap to 2-pin
1x 2-pin to 2-pin
1x 3-pin to 2-pin
2x hdmi to hdmi
2x short BNC
2x USB

2x AC to 2-pin

 

Asking $12,000/set OBO. Free shipping in the US or pickup in NYC.

There are lots more pictures of each unit so let me know if you need to see more. You can contact me at garethmanwaring@gmail.com

IMG_4075.HEIC IMG_4084.HEIC IMG_4090.HEIC