George Grammatikos

looking for a transvideo rainbow HD&HB

Bolt pro rx (I suppose generation 1)

iam looking to buy an extra Teradeck bolt receiver E mail me at georgesteadicam@gmail.com

Beach racket and swimming all the year ,sexercize too

I have 3 mags for sale make me an offer

iam still waitting answer for mk-v ,any other who can make my favorite mottor work again ?

WHERE CAN I SEND AN FMG 6 MOTTOR FOR SERVICE?(EUROPE)

you can always add weight to your monitor ,and an extra battery are the best and the most useful weight

i use to remove the arm from behind and take the hardness with me inside the plain ,i never had problem

Hi everyone I was looking at buying a B.Bel arm that was for sale over here(Australia) and may I say it took me over an hour to change the springs over from Heavy to light springs .As for the ride for me was nothing on the Pro arm Slightly better then a 3a. I never went ahead with it. just my 2cents worth Louis Puli HEY Louis , over an hour? maybe the arm use short springs (the are some of them out as Markus use diferent size elbow in the older arms )of course its not pro and the change look like a pain but its not so bad i had change them only twice when i use this arm and the second time take me about 10-15 min(i agree that its still a lot of time)but it cost 1/2 price of pro ,but my opinion is go pro its worth every cents !!!!

i used to work about 6 years with this arm (with heavy duty springs)it work great with big cameras litle hard with lightweight cameras(much better if you use light springs,Markus use to tell that you dont need the light springs but i thing it work better with the light springs,for light cameras(video 16mm) if i try to compare it with pro arm (i work 3 years now)its sure one step back but not so far away!Pro work with one finger from the lower to higher position B.Bel need two finger from midle lower to midle higher position and 3 or litle more power for the end positions my 2 cents George

Thanks Christian and Benjamin ,as i must find a solution for that until yesterday, i upgrade the inverter,i just add a 7812s regulator in the voltage input ,the kit work good the 7812s is warm but not extreme hot (2 ks4 working)

i Agree with Amando ,the cost of a dconverter is at 400$-1000$max and in the other hand you do not have to change monitor(3500$-7000$)and transmiter(....$)

Hi Julian this kind of cameras have an optical or image stabilizer (something like that )did you turn it off?

Hi can i power the ks4 gyro (ki-12-d inverter)with 14.8v battery?

i just finish a shooting for a feauture film with red and decimator ,i was working almost two months ,and many times under bthe hot sun no problem at all for the redbyte ,also i check that the unit work better in ntsc than pal

have a look at black magic video recorder ,can be a useful steadicam tool?

i use the bartech 8 years now have drop down many times (at least 8) and still work perfect ,its a great tool and Jim always behind his phone ,Thanks Jim

iam loooking for a lightweight clip on matte boxx for 130mm ,iam thinking the arri lmb 4a ,any alternative ??

i get mine a week before ,after 4 days shooting with a red camera the red byte works Great

iam looking for a red power cable asap thanks in advance

yes Lukas that i mean arri has cut over 30-32v (doesnot start as you said )but i have hear for moviecams (terror) and what about Red??

the problem is if you use two off them for 24v camera as the batterys will give 29.6v minimum and when are fresh chearged ???34v?32???ithink most cammeras have 30-32V fuse

Hi Erwin ,you are the man i suppose you will share with us photos with interests and news from Nab ? i woould like to be on nab ,maybe next year

Hi Guys ,i have a v2 gimbal and when i pan my rig 180 i am little out of balance ,prodably my gimbal is not center (4 years old),can i fix it here or i must send it to mk-v??