Nitin Rao

Hello .

Has anyone flown the Atom rig with the epic cameras. How has one managed on the arm lift capacity. Please give me some info.

Thanks

Nitin

Hi

I have complete package of the power pod classic with hand wheels and pan bar operations. Its in india and can be shipped any where around the world.

Thanks Jim

Hi

Could someone please help me with the connections for the RED camera start/stop. The connectors used for the same.

Thanks

Nitin

Hi Vijay

Its nice to know someone is trying to make a steadicam. we have been doing it for years, infact i have had them in use for over 15 years. you are most welcome to contact us.

Regards

Nitin

Thanks Louis

I am in the process of making some on my own. Will post some pics soon.

Regards

Nitin

Thanks

MIKE.

Hi Mike

Thanks. Could u pls let me know as to how much did it cost and wht size did it come in. Has the frame being included as a kit.

Cheers

Nitin

Thanks Robert,

Was looking out for something like a screen held in a frame. Has someone made one, something like the Windkiller from sunbounce products.

Hi there

I have had serious issues with strong winds throwing off the steadicam off balance. At times its difficult to hold off flags to cut off the wind due to the lights placed around the operator. How does one go about handling situations like this. I have heard of the windkiller kits, anything beyond this kit. please advice.

Thanks

Nitin

Hi there

Well u have quite a few choices with the 435 ES camera.

1. U could invert the stdcam upside down.

2. Depending if its a std Mag u do get brackets to fix on the camera. Chk on the Jerry Holway site.

3. Have the cam put in a low mode cage. ( i have mostly flown my kit in the same)

Hope this helps

Cheers

Nitin Rao

India.

Hi there,

I think the DP meant was the power surge, since the Red can draw upto 10amps. The bartech where as is also a 12volt run unit. Its possible the wires would have gone hot due to this. you can overcome this if u run the Red cam by its own supply (Red Brick batt).

Hope this helps.

cheers

Nitin

Hi there

Has anyone flown in a panavision Platinium with std fittings on a steadicam. What issues does one have to face apart from the excess weight, can one fly it in low mode. Please enlighten me with the facts of its possibility.

Regards

Nitin

Hi

could someone please help with with the lemo connector used on the panavision Platinium for powering the camera and its pin config. also the start/stop lemo pin with its pin config.

Thanks

Nitin Rao

Hi there

sorry abt the delay in reply. Have been busy on shoots here in india. Anything u need regarding a steadicam is very much available. Unless for Gyros. Pls carry them if u think u would ever want to use it. U need a segway or a ATV u are more then welcome to contact me. Just shot on the Red myself for a single take of 58mins.

Regards

Nitin Rao

Mobile: 919820051071

email: zerogravity2000@gmail.com

Hi

I am sure would have been really difficult to operate with that focal length. How did u manage to balance the kit. Would be nice to see a pic of the kit with the 300mm on.

Cheers

Nitin

Hi Erik

I too have had a similar problem, its matter of just tightening the allen screw which is located just on the same moving part. Hope it solves ur problem. Since its a U2c steadicam u would have not had a remote so u could even reduce the space in between the part moving.

have fun flying the kit.

Cheers

Nitin Rao

Hello

I have just got myself a new Ultra2 system with the U2 monitor. I have had a strange problem today using the video signal of a Arricam LT camera i could not generate the frame lines/ Horizon level on the monitor, the video signal was fine. I had to reboot the system every time i disconnected the video of the arricam to regain the frame line.

has anyone come across a problem like that is there a setting one has to change on the video assist of the camera.

Thanks

Nitin

Thanks to all for the help.

Regards

Nitin

Thanks Robin

I the earlier discussion someone has mentioned the Red cam drawing upto 6amps is that safe for the Ultra2.

Regards

Nitin

Hello

Need some help on the cable for the Red Cam. I have been through the forum here. Has any one powered the Ultra 2 with the red. Does it need any modifications apart form the power cable. The 3pin cam power on the sled to the red cam 6 pin.

Thanks

Hello

Hey has anyone flown in on the SI 2K camera on the steadicam. Could like to have some info on the same.

Thanks

Nitin

Hey Andrew

Its nice to know of u designing one. where r u from, since we in india (Mumbai) are also in the process in doing so. The test hardware have been made and cosmetic finishing is on. Its a little unique unlike other ones around and digital by design.

would u like to share some of your idea would be gr8.

My email id is getagrip07@gmail.com

Thanks

Nitin

Thank you for the info. Would also need to know the connections for the camera ON?OFF. I think its a Pana XL

Thanks

Nitin

Hello

could some one please help me out with the connections to the Panavision cameras. Need to know the Pin configuration for the power connections and also the camera On/Off for remote focus.

Thanks

Nitin

Email. getagrip07@gmail.com