Brad Hruboska

Sold!\

O - rings have been replaced as well, not shown in this pic, they were cracked, i have included 4 spares in the kit.

offering for sale, (1) Cinetape, with 2 x Sensor cables ( factory built , new) 2 X Arri RS 24V power cables ( factory built , New) 2 X P tap 12v , ( new aftermarket built, tested) Pelican 1400 case , new foam. 3200 USD.

Second unit has sold. One left in this batch.

had a buyer but deal fell through. Still available.

BUMP. OPEN TO OFFERS.

Bump. One has sold, one deal didn't complete ,so still two full kits available. One was recently serviced by Cinematography electronics , paperwork on hand , just in fall of 2018. in a box since October.

removing from sale due to lack of interest. Thanks.

Bump.price reduced to 3000.00. A great starter gimbal or backup.

SOLD Thank you, the Gyro kit has SOLD!!! thank you all who expressed interest.!

pulling this from sale for now. I haven't seen a offer that tempted a sale... Thanks for the interest none the less.

Selling my secondary K-6 Gyro kit with two gyros. This was conceived of as a rental kit adaptable to any Steadicam post or convertible to the original mounting bars with the Tommy bolts in both 1/4 20 and 3/8 16 bolts to allow direct mounting for hand held work in aircraft as well as Steadicam. The post mounts are native 2" (XCS),and have insets for 1.58" and 1.5" posts (Tiffen and Pro). It will fit practically any sled, and inserts are easily machined from Delrin. This was achieved with Pro GPI mount spuds ( now discontinued) and XCS post clamps. ( included) The Inverter is built for 14.4 v batteries so it will run fin on a cigarette adapter or modern Swit and AB style batteries. 2,500.00 USD complete.

latest software updated as well.

Offering for sale a lightly used Betz Wave 1, Works well, but now upgraded to Volt Gimbal. 6500,00 USD comes with (2) pro HD (not cinelive) power cables and one p tap power cable. comes with custom cut foam pelican case.

Offering an original Pro 1.5" post gimbal, this is the style that requires an Allen key to lock and unlock, it would easily upgrade to a VZ style gimbal. I have gone in another direction with my gimbal build and no longer need this . This is an XCS ergo handle for normal operating on the left side of the body. Offering with 2" grip . 3,500.00 USD. Located in Toronto. Shown here mounted on a scrap1.5" post

Betz tilt plae with Pro adapter mount for sale. works well has the usual signs of wear. Small cut away in top plate for a experimental build. does not impede function in any way. asking 600.00 USD

I have for sale (3) Cinetape kits. All come with extension horns, and the Arri Matte box mounting comb, and pelican 1400 cases. Two kits have (2) each of cables, 24v arri RS, P tap 12v, and sensor cables and custom cut foam insert.asking 3500 USD One kit has only one of each. 24v, 12v p tap, and sensor, pick and pluck foam insert asking 3200 USD. this was my personal one for my steadicam builds. it was just completely serviced by Cinematography Electronics this year. All have been tested and are accurate to the inch , all functions and displays are working. These units were on consignment with Sim Digital, but with the recent Panavision merger announcement i felt it was time to sell them off. PM me or email me at steadi@sympatico.ca Brad.

still looking?, upgrading a gimbal soon, might have one coming avail. PM me privately.

Am i crazy or did I see a nifty arm hanger for mounting directly to a inovativ cart ? I swore it was a 16X 9 product but i cant find it again. I want to free up the table space and the stinger on the Hill dock is not in the right position to clear the tray.

Mike, I'm also using a Gen 1 Bolt 2000, and it does work well, Funny enough it will pass PSF on the sidekick , but will ghost on the old receiver. Just yesterday we had an issue with the transmitter, which has suddenly stopped passing signal on the BNC ,SDI pass through circuit. Unit is still transmitting as per normal, but I'm wondering how much af a nightmare it is to get that fixed. if i want to keep the sidekick , what are my options for compatabilty, ? i understand the 3000 and sidekick are not compatible, but the newer gen 2, 2000 is? AN d yes pairing the sidekick to the gen one is possible, but it is challenging.

and thats not how you use it. its a SR 1/2 bracket and the block you have threaded onto the rosette screw goes on the handle dovetail on the top of the camera.

i had a fixer locally to get all the gear in and out.

if you knew what i paid for the first version ( with all the bells and whistles) you would have a meltdown. to its credit, its has been the best asset to my operating ever, i never went back......

Lawrence. they do sort of exist. Phil Cramer of Panavision toronto, built one for me but had to build a mini 3V circuit into the lemo. I know others who had burnouts but it always worked for me. there is the danger if the MDR is on unregulated power of zapping the Red, but i always run camera battery separate from the sled.

sale pending.......