-
Posts
30 -
Joined
-
Last visited
Reputation
0 NeutralAbout Jake Bulgarino
Contact Methods
-
Website
http://www.eastwardfilms.com
-
Skype
jake.bulgairno
Profile Information
-
Location
Los Angeles
-
Tiffen Steadicam Archer 2 SYSTEM w/G50X Arm and LX Vest - Location: Los Angeles - Venice, CA - $19,500 Purchased 12/2011 Archer 2 - SN#0212001S G50x - SN#G50X1211008A Just came back from TIFFEN for a QC and all electrical and balance is in fine working order. I will provide paperwork from service. The rig has been well taken care of and as you can see from the pictures it's in great shape. -Sled: Archer 2 sled with dovetail plate, IDX VMount (No batteries or Charger Included). 7" 16x9 MARSHALL Monitor. 12V or 24V DC output. Non-Motorized tilting stage. -LX Vest: pads dry cleaned, just came back from Tiffen fully checked out. -G50x arm - With 15lb sled ( 2x battery weight included), payload approximately 35lbs. Just came back from Tiffen fully checked out. -Archer 2 docking bracket -(1) Hex Wrench Included 1/4" -Thermodyne Case (all items fit in case) -Steadicam SteadiStand C-Stand Accessories -Archer2 Low Mode bracket ("F" Bracket) - to keep arm from whacking camera when operating in low-mode Most of my cables have been sold, but I have these. Monitor Cable - (Tiffen Part Number 800-0111) 8 Pin to BNC / 4PIN XLRF 3 Pin Lemo to 4 Pin XLRF (12V Power) 3’ BNC Cable 2’ BNC Cable 2 x Battery Weights Included 1 x G50x Carry Bag 1 x Steadistand w/ Bag $19,500 If Interested, PM Me at jake@eastward.com
-
Random Monitor Issue on New Marshall Monitor
Jake Bulgarino replied to Jake Bulgarino's topic in Monitors
One of my Marshall monitors was doing that, it was the processor. It needed to be replaced. JA Yea I figured it wasn't good. Where did you send it for repair? -
Random Monitor Issue on New Marshall Monitor
Jake Bulgarino replied to Jake Bulgarino's topic in Monitors
Good luck, you should be fine. The Archer 2 up to this point has been a pretty solid rig for me. Never been a huge fan of the monitor though. To make it worst my Dovetail Locking plate (today) is not locking a camera down that is well within its weight range. Iv tried to tighten down the screw and adjust it but it is not helping. I have a pretty long shoot coming up in october so I gotta move fast. -
Random Monitor Issue on New Marshall Monitor
Jake Bulgarino replied to Jake Bulgarino's topic in Monitors
haha, seriously. Yep I am going to email Peter today. Thanks. -
Random Monitor Issue on New Marshall Monitor
Jake Bulgarino replied to Jake Bulgarino's topic in Monitors
-
Hey everyone, I have a pretty new Archer 2 rig and every once in a while the monitor starts acting up. . I attached a picture so you can see what it looks like. Has this happen to anyone else out there? The only way I have been able to fix it is to turn the monitor off and back on and it is gone for awhile. Should I send this back to tiffen? Best, Jake
-
omg, got 3 seconds of decent footage
Jake Bulgarino replied to James Palanza II's topic in Steadi-Newbies
5600k not 3200k :-) -
Great Work!
-
Weight plate/block with screw holes.
Jake Bulgarino replied to Haris Pallas's topic in General Discussion
Janice Arthur's plates/cages are great! Just got a cage for my Archer 2 and couldn't recommend them more. -Jake -
Power Cubes & Charger
Jake Bulgarino replied to chip mead's topic in Steadicam Marketplace - For Sale
Hey Chip, Any idea where you got the case? Best, Jake -
Steadicam/segway behind the scenes video
Jake Bulgarino replied to Pedro Guimaraes SOC's topic in Vehicles and Mounts
Very cool! Thanks for sharing.