Search the Community

For sale is my well looked after Gpi-Pro Cinelive Sled. Reluctantly selling as I cannot afford to keep this sled anymore! Read carefully below outlining upgrades, modifications and improvements made! Supply in Gold Mount or V-Mount - read on... Starting Price is £16,500 (+vat if UK based). Roughly $22,140 USD / €19,075 EUR. Additional options outlined below! One previous owner, bought new from Optical Support in 2018. Upgraded GPI gimbal to Volt system in 2020. Upgrade was done by optical support. Replaced main Pan Bearing in 2025. Performs wonderfully! Replaced threaded post connector and receiver in 2025. A great sled from GPI Pro. Check out what upgrades are possible, as the sled is still fully modular. In the future, one could add the superior new Lower Electronics, etc. Possibly 1.75" Post....? Info from top to bottom: Topstage & Upper J Box Betz Topstage & Plate Shimmed to correct clamp pressure on betz plate. Other 3rd party plates also fit well. Cinelive Upper J-Box Electronics Modified to add a 2pin accessory lemo (0B - pin 1 GND), wired into the main 12v line (rather than thinner inadequate wiring from the previous connector). Upgraded HD-SDI BNC 75ohm inputs to better Neutrik sockets. Less worn than previous stock parts. Volt Control Box Cam-Jam rigid control box mounting to betz topstage. (https://shop.cam-jam.de/product/volt-mounting-system-high/). Much better than stock tiffen rod mount (also included). Custom volt control box small power cable with angled lemo connector. (spare included) Custom volt control box front mounting plate for low-mode monitor or accessory. 3/8"-16 threaded insert with arri pin lock standard + 2x 1/4"-20 theaded holes. Easily removable if not required. Lightweight anodised green aluminium. Centerpost: Standard centerpost II 1.5" from Pro. Replaced threaded part, outpost receiver & locking ring (bayonet mount) 2025. Replaced nylon balls 2025 for inner post that run down the channels when extending post. Post Tool included. Gimbal: 1.5" Gpi Pro Gimbal with Tiffen Volt. Standard grip version. Originally upgraded 2020. Serviced in 2025 though optical support, new improved shimming/centering assembly at tilt bearings. Latest firmware. Added rubber grip racket tape around gimbal grip and gimbal handle for improved control and better feel. Can remove if needed! Nice in cold weather! Installed new Pan Encoder + cable 2026. (spare included) Installed new Pan Bearing 2025 purchased direct from Pro for improved performance. Makes a difference! (spare/old bearing included) Standard Volt gimbal control cable. (spare included) (Spare volt belts included) Previous Gpi-Pro Gimbals parts included (non-volt parts). Gimbal steadicam tool included. Monitor Bracket and Monitor 3 Options here: Option A (most OK-ish option) +£0.00 Gpi-Pro Telescoping Monitor Braket + Transvideo 6" Monitor 5/8" telescoping rods Cam-jam Yoke to Pro/XCS style legacy spud. Transvideo 6" monitor. Not as bright as most recent transvideo monitors. 2x Lemo Power cables and HD-SDI cables included. Good for a starter, or backup. May be able to use with latest Gen5 battery rack from pro with these rods... Option B (Better if you have another monitor) + £800 / $1070 / €925 Superior Cam-Jam Quattro II Monitor Bracket & Wide Yoke (no monitor). Great telescoping rigid monitor bracket and Yoke. Can include the mounting arms for SmallHD 703 (see picture) Other mounting parts for other monitors available at cam-jam.de Option C (best option) + £1800 / $2415 / €2080 Superior Cam-Jam Quattro II Monitor Bracket & Yoke + SmallHD 703 Monitor. Includes smallHD 703 monitor with matte screen protector. Used scratches & marks but functions fine. Includes custom flat weight plates for adding weight to the back of the monitor to help with dynamic balance. Stackable. Includes combination power and 2x HD-SDI cables. Use one to loop out of the monitor and back up the 2nd HD-SDI line in the post for an additional output in the topstage for a low mode monitor. Lower Cinelive J-Box Includes x2 Jumper Blocks. 12v all parallel block. Any plate combination can be used. 1, 2, or 3 batteries. 12v (14v) mode only. Shares the load between them. Standard 12/24v block. 14v from positions marked "C/M". Combine with battery in "A" position to create 24v. (Note: "A" position can change based on preference - see Battery Hanger section below). Upgraded HD-SDI BNC connectors 75ohm to Neutrik. Less worn than previous. Battery Hanger GenIV. Lighter weight than the previous GenIII, and makes a shorter sled ~25" fully collapsed (preferable operating feel to me). Modification: Quick change battery plates: Added thin custom aluminium plates with multiple hole patterns. Allows the following: Quick change from Gold Mount to V-mount by swapping plates. Can be done on set. Battery plates are on quick release connectors. Plates use M3 socket head cap screws. Great for travelling if you need to hire different battery types, eg different countries' or rental house's availability! Can change orientation of the battery plates. For AB V-Mount plates which have the same mounting hole pattern, the plate has to be attached backwards otherwise the battery can't be mounted due to the post/j-box in the way. Can move the plate under the post further back if more weight is required away from the monitor for dynamic balance. Good to have options! Can swap the rear 2 plates using the connector inside to determine whether the lower (default) or upper plate is designated "A" for 24v mode. Only weighs an extra 150g / 5oz in total for 3 plates which helps adding some mass to the lower stage of the sled. Upgraded Shottky diodes in Gold mount plates for slightly lower voltage loss. Can Supply AB Gold Mount or V-Mount Extra set of 3 other plates w/diodes installed (+£250 / ~$340 / ~€290) Case: Pelicase 1630 included with cut out foam Dock Tiffen Volt Dock Included Additional Cables 24v Rencher Cinelive -> Arri Alexa 35/265/Mini/MiniLF/Amira Coiled power cable included. Selection of HD-SDI BNC cables 14v Cinelive -> 4pin XLR power cable Spares: Spare Tiffen Volt Control Box Rod mount for Betz topstage Spare Post threaded connector Spare pan bearing (old bearing) Spare Volt control box power cable Spare Volt Gimbal Cable Spare Volt Pan Encoder+cable Spare 10A & 5A Klixon push pull fuses for Lower J Box. Spare volt gimbal shims and belville washers. Spare Volt belts. Please email me at jake(at)jakemcclean.com for more info, any questions or more pictures! Also available may have some Jerry Hill 1.5" docking rings if you already own or prefer to use a JH dock. spin1.mov

FOR SALE Cam-Jam Quattro Universal Monitor Arm with integrated yoke I am selling my Cam-Jam Quattro Universal Monitor Arm with integrated yoke. It is less one year old and looks brand new. It was on my rig that I just sold and my new rig already had one on it so I don’t need this. The Cam-Jam Quattro Universal Monitor Arm is without a doubt the best monitor arm I have ever used. It is rock solid, light-weight and completely vibration free thanks to it’s four point mounting system. It allows you to infinitely adjust your monitor position and instantly go from high to low mode positions all with no change in balance. You can use the arm with almost any monitor from Small HD, Transvideo, Boland, Odyssey, Ikan, Cinetronics, Nebtek or Marshall with the addition of a monitor mount from Cam-Jam (not included here - cost is $50-$100 depending on model). I also have (for an additional $50) an Universal Adapter for backup monitors that allows all monitors with a 1/4”-20 threaded hole on the bottom to be mounted to the Quattro Monitor Arm, not using the yoke. With it’s 2” diameter clamping ring, you can mount the Quattro Arm on most any stage of any Steadicam rig as custom adapter rings are available for any post diameter (I am including one 1.5” and one 1.9” adapter rings). For more info see the Cam-Jam website at: https://shop.cam-jam.de/product/quattro2-monitor-arm-with-yoke/ The price new is 1,230.00 € (about $1,450 US) with the two adapter rings. I am asking $1,100.00 If you are interested PLEASE EMAIL ME DIRECTLY do not post questions here, I don’t check it often enough. Direct emails will get very quick responses. Thanks, Stephen Consentino Email: film.maker@me.com Cell: 914-837-0120

I bought this as part of a package deal and currently carry a monitor that uses a different yoke. Quattro I can be updates to Quattro II with these parts: https://shop.cam-jam.de/product/upgrade-kit-quattro-monitor-arm-2/ This yoke currently sells for 190€ ($215.00 USD) plus shipping from Germany. I’d rather see it get used than sit on my shelf. Please email for all inquiries.

Hi everyone I'm selling my Cam-Jam Quattro Monitor Bracket. It's in pretty good condition. Only couple of minor scratches, but perfectly working. I had used it on the outer post of a Betz RIG for a Transvideo 6" X-SBL. I'm asking 800 EUR € For inquiries please e-mail me at: info@ozzyoksuz.com Cam-Jam Quattro Monitor Bracket for Transvideo 6” 1.Quattro Monitor Bracket 2.Reduction Ring (for Betz RIG outer post) 3.All mounting screws and adaptors for transvideo 6” x-sbl included Shipping within EU preferred, Buyer pays for shipping and upcoming money transfer fees Cheers

whats shakin yall?! has anyone played around with external tiltheads, like the cam-jam or chrosziel? i like the idea behind the cam-jam. not worried about having to rebalance on the go or having to play around with dynamic balance, thats all part of the job. i have read around a bit but wondering about some personal stories. could be a fun item to have in the kit regarding the cam-jam : ever any issues with plates slipping or any vibration? the betz claims to be vibration-free. is it the same as the chrosziel model? brett.