Search the Community
Showing results for tags 'analog'.
-
Mounting 16mm on Artemis Cine broadcast
Fernando A. Vazquez Schmidt posted a topic in Steadi-Newbies
Hi, I have been asked to mount a 16mm camera on a Artemis Cine broad cast, asking local Steadicam OP´s on what I need to have in mind the Image monitoring is one of the subjects I haven´t thought about, what is best for converting analog to digital? and what other things I need to have in mind? Thank you for your time. -
Analog Bartech Focus With M-One Motor $1,800.00 Shipping in the Lower 48 States in the USA is included with purchase Buyers elsewhere pay for shipping Meticulously maintained. This was my backup and very seldom used. - BFD Transmitter - BFD Receiver/amplifier - M-One Analog Focus motor - Matte box rod receiver/amp mounting bracket - Steadicam Motor Rod Set - 6 Lens gears - Various rod adapters - 19mm universal mounting bracket - 2.5" universal extension/offset bracket with 19mm attachment tubes (1.12" and 2.12" length) - 3 spare antennas for Transmitter - 2 spare antennas for Receiver - Hard cases for both the BFD system and M-One motor - Cable 5795: BFD Receiver to Video Camera 12-Pin Run/Stop cable - Cable 612:BFD Receiver to M-One/Heden 5-pinb Motor cable - Cable 6066: BFD Receiver to Arri 435/535/Arricam/Moviecam Run/Stop cable - 5-Pin Lemo to 5-Pin Lemo - 2-Pin Lemo to 2-Pin Lemo –(I power from the sled with this one. One end is 2 pins in a 3 pin casing)
-
M-one motor (recently serviced) Lots of cables including: -Pro power -Aaton power -dtap> power -2pin>2pin -Back up antennas for motor driver and hand unit -Marking rings & 15mm>19mm step up rings -Motor gear pitch wheels and backup motor 5pin>5pin cables Motor Driver has a Pro DB bracket receiver so you can slide it onto your diving board if you're sporting a DB. Comes in a peli with a backup 9v and a really useful motor bracket that sticks motor out further and gives more mounting options. *things to note*: (HU battery wire/spring was stretched recently on a show when switching batteries it stuck to the battery upon removal, works fine you just have to push the battery more than usual to slide the door closed on the HU because the spring isn't fully compressed.) $2,900 Located in LA.
-
Selling my analog Bartech kit. Asking $2500, free shipping within CONUS. - Analog Tx/Rx (S/N 0748) and antennae - Heden M28P-90103 motor - D-tap to LEMO power cable - LEMO-LEMO power cable - "Dogbone" for 15mm rods - 10k pot for thumb control - Extra 32-pitch and iris wheels for 15mm mounts - Extra mounts (small black one needs a new screw to tighten) - Extra strips for handwheel - Case with foam Would be great for someone just starting out (as it was for me.) Works flawlessly, I just need the money for something else right now.
-
I need to purchase a replacement motor for my M1. I need either an M1 with super low hours, or a refurbished one, or an equivalent motor from another manufacturer that will work with my analog Bartech. I'm local in LA. Please text me at four 2 four two zero two one 7 zero 5. Thanks! -Thor
-
Selling my almost brand new Blackmagic MiniConverter SDI to Analog 4K. The unit is in perfect working condition with the only damage being purely cosmetic (a scratch or two with some light damage to one of the dip switches; does not affect any functionality). My reason for selling is that I need some extra cash and this is my backup downconverter. I am also including a P-Tap cable with a built-in 12volt DC regulator (built by Terry West, so you know it's quality). The regulator is a must; the converter only runs below 15v so unless you deplete your charge to under 15v you won't be able to power the unit from your sled. Brand new, the unit is $280 and the cable was around $200. Looking to get $420 for it, OBO. Buyer pays shipping, or we can arrange a pickup (located in Van Nuys in LA). Email: aaron.gantt@gmail.com Cell: 704.322.6889
- 3 replies
-
- blackmagic
- black
-
(and 7 more)
Tagged with:
-
WTB: Analog Bartech System with M1 Motor
Mike Quill posted a topic in Steadicam Marketplace - Wanted
Please PM or email me if you have one for sale. Thanks! Mike mq@mikequillproductions.com -
Hey I'm currently looking in the market for a used bartech and motor package. I'm located in LA so a local purchase would be great. So if your looking to sell one please feel free to shoot me an email. Thank you. thomascolefedak@gmail.com -Tom
-
- bartech
- follow focus
- (and 4 more)