Premium Members Michael Wilson Posted February 4, 2012 Premium Members Report Share Posted February 4, 2012 I have a low mode bracket for a pro arm. My mk-v gimbal handle doesn't have a hole in it to accept the pin to use the low mode bracket. Can I take it to a cnc guy to drill this? Should I take it to a cnc guy to drill this? Will I break anything? Do you guys use your low mode brackets? or just flip the sled over? Quote Link to comment Share on other sites More sharing options...
Premium Members Thomas K. Jensen Posted February 4, 2012 Premium Members Report Share Posted February 4, 2012 Yes, you can drill a hole in your gimbal handle for the low mode bracket. Jerry mentioned on the workshop, that if you have an older system (or in your case a system without the low mode hole) you should just drill one. Quote Link to comment Share on other sites More sharing options...
Richard James Lewis Posted February 4, 2012 Report Share Posted February 4, 2012 I wouldn't drill anything. I'd be worried that you were weakening the handle if the hole wasn't drilled in the right place. I had an mk-v gimbal for 4 years and never ever used a low mode bracket. You have enough clearance with a handle that long, so you aren't hitting the sled, so you do not need to invert the handle to remove the obstruction. Just pop your bracket in upside down and use a post collar to secure it in the arm. This will give you a few inches lower, but by then you are probably all contorted trying to get your grip that low on the post comfortably. Plus most mk-vs had a 4 stage post, so you don really need to get your hand that uncomfortably low anyway. Rick. Quote Link to comment Share on other sites More sharing options...
Premium Members Jerry Holway Posted February 4, 2012 Premium Members Report Share Posted February 4, 2012 The reason to use a low mode bracket (F-bracket, J-bracket) is to place the working end of the arm back in the "gap" between the camera and battery - this is especially important when flying heavy cameras, with the gimbal close to the stage. If you don't, you can't make switches; the arm will hit the camera. And the camera will fly higher, so if you want to go lower... Now for the drilling: It's important to not trust any sort of clamp to hold the gimbal handle to the inverted "arm post" of the F-bracket. Danger Will Robinson! Don't worry about the hole and strength; just make the hole about 3/16th inch in diameter and use a #10 hardened screw (or a quick pin from McMaster Carr or other supplier). The hole must go all the way through so the pin is in what is called "double shear." It's much stronger that way. A 1/8th inch diameter hole is fine as well, perhaps better for a 5/8ths post system. I wouldn't drill it free-hand; and it will go better (more likely to be well centered) if you do it on a mill. Jerry Quote Link to comment Share on other sites More sharing options...
Stig Indrebo Posted November 13, 2016 Report Share Posted November 13, 2016 How important is the clamping on the gimbal to hold the rig upside down? My rig (Glidecam x-45) doesn't have a clamp on the gimbal nor a hole for the pin. Considering drilling the hole, but if the clamp on the gimbal is important here, I won't. Quote Link to comment Share on other sites More sharing options...
Premium Members Jerry Holway Posted November 13, 2016 Premium Members Report Share Posted November 13, 2016 As I said before, you must have a pin through the gimbal handle if you use an F or J bracket. A clamp won't hold and is not safe. Nor are the set screws in a J-bracket like the original Master Series one... see the book! Quote Link to comment Share on other sites More sharing options...
Stig Indrebo Posted November 14, 2016 Report Share Posted November 14, 2016 Hi Jerry, thanks for the reply. Yes, I'm aware that the pin is needed - but I was wondering if a clamping gimbal handle also was important, or if the pin was enough to hold it all. Quote Link to comment Share on other sites More sharing options...
Premium Members Jerry Holway Posted November 15, 2016 Premium Members Report Share Posted November 15, 2016 clamp is of no value. Pin is everything Quote Link to comment Share on other sites More sharing options...
Stig Indrebo Posted November 15, 2016 Report Share Posted November 15, 2016 I'll take my rig to a cnc guy and get that hole drilled, then. Thank you, Jerry. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.