Jump to content

Steadicam M1 Volt


chris fawcett
 Share

Recommended Posts

  • Premium Members

More on #7, "getting confused." What you describe in your question it always handles like a charm. Even flipping it upside down, whip panning, and doing all sorts of wild things all at once (we've watched folks try this at demo's...) and it has always worked.

  • Upvote 1
Link to comment
Share on other sites

  • 4 weeks later...
  • Premium Members
Hello,
On the two pictures below I noticed that the motors of the M1 volt are setup at the oposite side of the gimble.
The setup on Photo N°1 seems more suitable for goofy (more room for the hand Under the gimble + easier to put on the shoulder for rest position)
The setup on Photo N°2 seems better for regular ops
Can we choose the side of the setup when we order the M1 Volt??
Thanks
Grégory Dupé

post-11865-0-17789300-1527782292_thumb.jpg

post-11865-0-63315300-1527782308_thumb.jpg

Link to comment
Share on other sites

  • Premium Members

Yes, viewing seems more important than clearance for the operating hand; photo 1 is more typical for regular operators. BTW, I thought the hand clearance would be the deciding factor when it was designed... so for once something was designed for goofy first.

Link to comment
Share on other sites

  • Premium Members

the M1 Volt motion tracking algorithm completely covers 360 degrees of roll, tilt, pan with no glitches or dead zones. It always knows camera orientation and pointing direction over the full sphere of motion and does not get lost or confused. Like all inertial navigators it will very slowly lose horizon if you accelerate for minutes at a time. Recovers smoothly when acceleration ceases.

Steve Wagner

  • Like 1
  • Upvote 1
Link to comment
Share on other sites

  • Premium Members

Marco, if you remove the motors, it's still a gimbal like any other, so it can be re-centered.

 

The M1V will compensate for slight imbalances in not so perfect gimbals, and not so perfect static or dynamic balance by the operator.

 

Of course, the more perfect the gimbal and balancing are, the better it works.

Link to comment
Share on other sites

  • 3 months later...
  • 2 months later...

My apologies for resurrecting an old thread.

Tiffen shipped a docking bracket that grabs the sled by the handle on the gimbal. Holding the sled by the gimbal makes sense because of the cables wrapped around the post on the volt might be at risk with the Jerry Hill docking system.  But with a little care, that shouldn't be an issue.

What's everyone using the m1-V doing for docks and carts and Moses poles?

Stirling Bancroft csc

Edited by Stirling Bancroft csc
vanity about grammar
Link to comment
Share on other sites

  • Premium Members

The docking bracket helps when using the Volt in several ways, including preventing the small possibility of injury to the cables, and preventing a much bigger possibility of injury to the Volt motors and motor electronics.

Also, the dock is padded, so there is less shock on the gimbal bearings when docking. A related minor concern, but still an advantage - no little bits of anodized aluminum get ground off and potentially drop into your gimbal. The gimbal is always at the right height for docking, regardless of how long or short the sled might be. The gimbal can get closer to the stage than with a traditional dock. The primary balancing stud is low and close to the stand center, so there is very little lifting off the dock for balancing (less effort!) and nothing to move around for balancing. Nothing slides or interferes with docking. The over-centers locking lever is easy to use and it is clearly engaged or not, and there is a secondary lock on the OC lever.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...