Jump to content

Recommended Posts

  • Premium Members
Posted
As much as I dislike the Red Camera the turn around is impressive...

 

that was indeed fast! then again I used to do that in 36 hours, right?...

 

they could tighten up that edit considerably.

  • Replies 106
  • Created
  • Last Reply

Top Posters In This Topic

  • Premium Members
Posted
Enyone used the supposed mountning-bracket to the Decimator?

Got a red small bracket with the Decimator, but no screws.

 

I looked at that thing and it didn't look like any of the holes lined up with ones on the decimator or anything... maybe I was missing something. They could have been under velcro.....

 

~Jess

  • Premium Members
Posted
Enyone used the supposed mountning-bracket to the Decimator?

Got a red small bracket with the Decimator, but no screws.

 

I looked at that thing and it didn't look like any of the holes lined up with ones on the decimator or anything... maybe I was missing something. They could have been under velcro.....

 

~Jess

 

 

I could not figure out it's alignment either.

 

Rich Davis

LA

  • Premium Members
Posted

Maybe the holes line up with some HD camera somewhere and then you add velcro? Or more likely they are an extra or mismade part of one of their products that someone decided to throw in as a freebee because then they wouldn't have to throw it away.....

 

~Jess

Posted

Hi.

I contacted Redbyte. This was their answer. Tryed it, and it's not that good fit actually. I'll probably go with velcro.

 

 

"It is mounting bracket, that is used to mount the Decimator to the back of a rack, behind the monitor. A picture is attached, showing it installed.There are two slots on the back of the box that have threads for attaching it with two M3x6 screws."

 

Bye

 

/marco

post-7584-1238539414_thumb.jpg

  • 2 weeks later...
  • 2 weeks later...
  • Premium Members
Posted
Is anybody having the the 4 pin Lemo conversion on the Redbyte done and if so who did the conversion?

 

Thanks.

 

 

I did it myself, it's really rather simple as the circuit board easily slides out and you can clearly identify the solder points for Power and Video. Be careful to make sure all of your polarities are correct as the unit doesn't have reverse protection (I saw a fried unit the other day from this very issue) A picture of mine can be found earlier in this thread.

  • Premium Members
Posted
Is anybody having the the 4 pin Lemo conversion on the Redbyte done and if so who did the conversion?

 

Thanks.

 

 

I did it myself, it's really rather simple as the circuit board easily slides out and you can clearly identify the solder points for Power and Video. Be careful to make sure all of your polarities are correct as the unit doesn't have reverse protection (I saw a fried unit the other day from this very issue) A picture of mine can be found earlier in this thread.

 

Thanks Iain. I had a couple of inquires from friends of mine. I wouldn't mind messing around with mine but I don't want to take the chance on their Redbyte's.

  • Premium Members
Posted

I had an extensive discussion with the Redbyte folks about this at NAB.

 

The factory is not planning to reconfigure the power connector at present.

 

Perry Drogo at TECADS (N. American distributor) is considering doing a run of mods as required. We have discussed simply replacing the power connector with a Lemo jack, which is simple enough, but also the possibility of making this a combined power and video output like we are used to with various other components which would allow a single cable to the rig. The complication here is that wiring the video pins up while keeping the BNC active means splitting the signal, just like using a "T" barrel, which we all know cuts down the voltage and can thus affect the image. The case is too small to accommodate a VDA board.

 

I have tossed out the idea of a circuit that senses when a BNC is attached and switches the video between the Lemo and the BNC, maintaining proper 1 volt signal, and Perry thinks that is possible. Seems like the best of both worlds.

 

More news as it develops.

  • Premium Members
Posted
I had an extensive discussion with the Redbyte folks about this at NAB.

 

The factory is not planning to reconfigure the power connector at present.

 

Perry Drogo at TECADS (N. American distributor) is considering doing a run of mods as required. We have discussed simply replacing the power connector with a Lemo jack, which is simple enough, but also the possibility of making this a combined power and video output like we are used to with various other components which would allow a single cable to the rig. The complication here is that wiring the video pins up while keeping the BNC active means splitting the signal, just like using a "T" barrel, which we all know cuts down the voltage and can thus affect the image. The case is too small to accommodate a VDA board.

 

I have tossed out the idea of a circuit that senses when a BNC is attached and switches the video between the Lemo and the BNC, maintaining proper 1 volt signal, and Perry thinks that is possible. Seems like the best of both worlds.

 

More news as it develops.

 

 

In all of my experiences with video signal strength it isn't until you actually plug something into the second connector that the voltage drops. Personally I can't see having to use both the LEMO output and the BNC output at the same time. In my case the Video input plug on the Rig goes to a video DA and is distributed from there to the SD devices (recorder, transmitter, monitor)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...